Having to do roof repairs once in while is quite normal for homeowners. Some may want to spend some money and hire another guy for the job. But with the increasing familiarity of DIYing, people find it more appropriate to take over these minor home tasks themselves and not bother spending if it’s not necessary.
However, roofing tasks can’t be quite considered a minor chore. Since there’s a lot of risk and concerns related to it that need your serious ponderation before doing anything at all. And if the case is about a steep roof, then the severity of this matter becomes ten times more concerning.
Today we would like to talk about DIYing a particular tool that can greatly help in such chores. Let’s talk about how to make a roof ladder hook, a tool that can quite lessen the burden of those risks and worries.
Read Also: How to Use a Ladder on Stairs Safely
Here’s Everything About How to Make a Roof Ladder Hook
Pitch is usually referred to as the roof’s steepness and if angle associated seems too steep, then walking on it is not safe at all. You must find out way or tool that can help in anchoring. And the most common and handy tool that can be in charge is ladder roof hook.
The hooks basically keep the ladder’s top part secure with roof. Opposite to the hook, you should see wheels too. These are meant for easily rolling ladders up and down. To make your own version, let’s keep things simple.
You will require a stout steel piece. It should be somewhat 3/8 by 2 in measurements. We will basically bend it using a rebar cutter for making a hook. Place the steel piece over the rebar cutter to start with bending process smoothly. You want a friend to hold one end of the half of your steel while you’re working on rebar cutter’s handle.
The other half of steel needs to be laying straight on surface. So that the bend gets right pressure from both sides to create proper shape of a roof hook. As you bend steel, ask your friend to pull the laying body of metal towards himself to readjust next bending part on it.
That way you want to work on the entire laid half of steel. And make it curved like a huge hook shape. You can reposition the steel’s curved part to make it a nice crescent shape. You may need to try multiple times for creating the right bend. So, make sure you have more than just one piece of stud steel. Once you get an ideal hook-like shape that comes with the proper clearance to work alongside a ladder, you’re allowed to stop.
If you don’t have a rebar cutter then simply getting a ladder hook kit can solve your problem. In that case, creating the whole setup of a roof ladder hook is what we’ll be talking about next.
Decide the Measurements
The roof edge and landing will have a specific length that you need to decide first. After counting this distance, add around four inches extra to this length. Now you have the measurements for following to cut first utility lumber of 2-by-4 inches. You’ll need two lumber pieces with this measurement as the ladder rail length.
Place the rail on saw by keeping it on edge and side by side. You need to secure the ends with clamps next.
Ladder Rung Marks
At this point, determining the layout marks for ladder rungs is applicable. Start from the rail’s randomly chosen end. Then you want to make a layout every 12 inches apart and keep on going this way. A builder’s square can help you for maintaining the accurate 12 inches gap.
The 1 by 4 inches utility lumber will play role of ladder rungs. That way you need to figure out its width next. Usually, 3 and ½ inches work best here. Across the edge of rails, try to keep on marking additionally. The gap between marks should be exactly 3.5 inches.
Bring your circular saw for some work. Set blade depth to the thickness of 1-by-4 inches lumber. The standard measurement here is somewhat ¾ inches. Use a circular saw for making crosscuts on rails. You can remove the c-clamps after that. Then lay the rails flat on top of your sawhorse.
From each rail, try chipping about 3.5 inches of wide sections next by using a hammer and chisel. To work in the middle section of saw cuts, make use of chisel. The rung recesses you create needs to be of ¾ inch. Make sure you have the number of recesses in one rail noted down somewhere. Typically, a 1-by-4 -inch lumber should give you 16 inches long pieces to use as ladder rungs.
Attach Rungs to Rails
Maintain 16 inches of the gap in between, place rails next. While doing so you want to ensure the recesses are facing upwards. In recesses lay carefully the ladder rungs. Flush the ends onto outside edge of rail. To connect rungs to rail, use screw tip drill, and some wooden screws. You need two screws at least for each end. So that the attachment is as stable as possible.
The place on roof that will hold ladder against it needs to be ideal enough to provide right balance for you to climb without a problem. Using the 1-by-4 inches lumber, cut down two additional points now. These should be 16 inches in length.
Now use hooks next as ladder stabilizer with padding or material that does moderately less damage to the shingles of roof. Using a kit here will give you the strongest installation. Go for the ones that come with wheels.
- The Best Way to Seal Bathroom Wood Floors
- How Deep Should Floating Shelves Be In The Kitchen | It Depends
- Vinyl Vs Laminate Flooring Pros and Cons [In-Depth Comparison]
- How To Remove Bona Hardwood Floor Polish: 4 Steps to Complete
How do You Attach a Ladder Hook to a Roof?
The process of roofing ladder hooks may sound confusing but it’s actually pretty simple. First, you need to ensure both rungs have ladder hooks attached well with suitable wingnuts. Next, you want to bring the ladder up by pulling it towards roof. The wheels should be facing downwards while you pull the ladder.
It should be rolling across the shingles but there must not be any knocking. From where your vent or chimney is located, simply position the ladder at least 2 or 3 feet away. So that as soon as it comes to position, you have enough space and can turn over when in need.
The wheels should come in contact with shingle’s topmost row, push ladder upwards until it touches. To make the hook face downwards, simply turn it over next. You want to move the ladder back and forth multiple times. This is to check if the ladder is set safely.
Once you are done, go backward with the entire process. Let the ladder go forwards at least one or two inches. Making the wheels facing towards roof, next you want to turn it over. Bring it back down the roof by rolling. Make sure to always carry a safety roof with a ladder. The whole raising and lowering task will become greatly easier with this.
Also try to avoid climbing ladders with any tools in hand, no matter what situation. Keeping one foot on the ladder with both hands firmly holding it is what you must maintain while climbing to keep things safe. A tool belt can be helpful for carrying the tools and keeping hands free.
You May Read This: How to Use Ladder Jacks by Minding Safety Concerns
Space up there is pretty risky when you don’t take necessary measurements beforehand. And so, learning how to make a roof ladder hook and using it for such needs can really help a lot to keep things mishap-free.
If you don’t feel like going through the whole hassle of DIYing then know that there are quite a few handy and inexpensive roof ladder hooks available on the market. Purchasing one of those can also be a good route. Just make sure you pay attention to all the specifications and decide on a suitable option that sounds solid enough to keep you protected throughout whole roof job.
This is Autem Decker. Main Author of ‘TheHomeDigs‘. You may not find her on the list of top 10 contemporary Canadian interior designers, but everyone who knows her says she was born to be an interior designer.
She makes her plan in her head and draws them on her years-old dairy with a note in the corner. The way she plays with color and shape amazes us.
Connect Her On – Twitter